Did you know?

The Litter-Robot 3 is equipped three LED lights to indicate certain statuses and faults with your unit. If all three of these lights are flashing in one of three combinations, it is an indication of a Globe position fault. You will also receive a notification on your phone if you use the Whisker App.Litterrobot won't cycle. Blue light keeps flashing, tried hard reset. Changing out wires, and recalibration. None of those have worked. I clean it often so there is no poop that would set it off please help! Dust/litter/dirt on the sensor where the drawer is so it thinks it's full. I usually take a Q-tip and lightly brush the sensor to clean it.Press the Cycle button. Once the Clean cycle is complete, the unit should go back to blue ready status. If your unit returned home and displays a solid blue light, you've been …After turning it on or after a cycle, the blue yellow red lighting sequentially. If the Open Air unit cannot find Dump and/or Home position, the control panel will display 3 lights blinking. If you have recently disassembled your globe please advise. Please remove the globe and check the black gear connected to the motor.1.) Leave your unit powered ON with the blue blinking light engaged and unplug your power supply from the base 2.) Wait 10 seconds, then plug the unit back in. 3.) Allow the unit to complete a start-up cycle. If the light is solid blue, the code has been successfully cleared. If the light is still blinking, let's proceed with troubleshooting.Oct 18, 2016 · Step 10: Manual Cat Sensor Activation. Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn off and the red light should come on. You've activated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allow the Wait Time (3, 7, or 15 minutes ... Completely close the Litter-Robot app. While the unit is at the Home position with the solid blue light, unplug your unit from the base, not the wall. Wait 15 seconds, plug it back in, and allow it to cycle until the …Dec 10, 2021 · 1. Empty the Drawer. On the Litter-Robot, you have a drawer that collects the cat litter. If it becomes full, the blue light will blink rapidly. But if you throw out the mess, the lights should go off. Before returning the drawer to its compartment, remember to place a new liner into the container. In addition to these buttons, there are three lights labeled “ready, cycling, and timing” Ready. When this blue LED light is solid, it means the Litter Robot is ready for your cat to use it. If it is flashing, this means that the waste drawer is almost full. Cycling. The solid yellow LED light indicates when a clean cycle is occurring.If YES, you are done. Re-position Globe and verify that it completes a clean cycle (in this case adjustment of the cat sensor was not needed). 5. Turn the Base upside down so you are facing the bottom surface. Find the round black adjustment foot and simply turn it Clockwise (2) full complete turns (720 degrees). 6.Reboot your router. Completely close the Litter-Robot app. While the unit is at the Home position with the solid blue light, unplug your unit from the BASE, not the wall. Wait 15 seconds, plug it back in, and allow it to cycle until the solid blue light comes on (“Ready” status). Open the app and follow the steps.Phone and Chat support available Mon-Fri: 9AM-5PM EST or submit a ticket anytime. Chat with us. Find answers, guides, & solutions for your Litter-Robot. Your first stop for answers and solutions to your Litter-Robot questions.Get best self cleaning automatic cat litter box and never scoop again! Even if you are a cat lover, changing out the litter box and scooping poop is never going to be pleasant. Eco friendly Litter robot automatically splits waste, flushes waste away and washes itself clean. Great for multiples cat and kitten.Litter Robot 3 not reversing during cycle. My Litter Robot 3 has been having a weird issue for the last two weeks. When it cycles, the globe rotates counter-clockwise until the hall sensor detects the magnet on the globe. It then stops, like it should. Then it's supposed to rotable clockwise to return to its home position, when the hall sensor ...1.) Leave your unit powered ON with the blue blinkiA full yellowish light on your Litter-Robot 3 control panel You’ll most commonly notice a flashing or blinking blue light on respective Litter-Robot 3 control panel. On blue light is called the Drawer Full Indicator, which …If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the Cat Sensor or Bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful. If your unit is not displaying a solid blue light after ... The Litter Robot 3 control panel provides the main Power Press and release the Power button to turn the robot ON of OFF. The robot will begin a clean cycle when power is turned on. Press and hold, while at the home position, to enter night light setting mode. Cycle Press and release the Cycle button to start a clean cycle. If already cycling, press Cycle to pause; press again to resume a cycle. The over-torque fault would appear if something blocked the robot’s rotation during the cycle… if one of the cats tried to enter or if some clumps blocked the motor somehow. 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base. 2.) Completely close the Litter-Robot app. While the unit is at th

Cycle Press the Cycle button to start a clean cycle. If already cycling, press Cycle to pause; press again to resume a cycle. A long press, while at the home position, will enter sleep mode. Reset weight scale. will enter night light setting mode. If already cycling, press Reset to pause a cycle; press again to cancel a cycle.Here's what I told Litter Robot, " Every time it’s used, it half cycles and I have to power it off and power it back on for it to cycle. Pushing the “cycle” ...Quick question. I got a litter robot 2 for about 2 years. It stop working today. The “empty” and “cycle” bottoms doesn’t work but only reset bottom works and “ready” is flashing blue. If I push the “reset” bottom, “cycling” is flashing yellow in 4 times per sec. The problem didn’t solve after I cleaned up pinch pins.The unit will cycle two additional times before it will no longer automatically cycle. If your unit has a flashing blue light, this indicates that the Waste Drawer needs to be emptied. Emptying the Waste Drawer when indicated is important to ensure that your Litter-Robot continues to cycle automatically. TroubleshootingThis video shows you how to get all 3 lights on the Litter-Robot 3 to stop blinking. Litter-Robot 3 Buying Options: Worried about your cats using... | Amazon, house cat, freight transport,...

There can be a few causes for this, main one being the LR hasn't been cleaned in a while allowing enough litter to accumulate on the top of the base. This results in the globe having to rub against the litter causing excessive drag. Another is the gear box for the drive motor is running dry on lube slowing it down making the motor work harder ...Power Press and release the Power button to turn the robot ON of OFF. The robot will begin a clean cycle when power is turned on. Press and hold, while at the home position, to enter night light setting mode. Cycle Press and release the Cycle button to start a clean cycle. If already cycling, press Cycle to pause; press again to resume a cycle.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. How to fix the blinking blue light on th. Possible cause: Page 31 Cleaning the Globe Press the Empty button to cycle the Globe clockwi.